Grove 103100124 Shield for Arduino Nano provides you a simple way to connect with Arduino Nano and also Seeeduino Nano. This shield pulls out the pins of the motherboard and expands to 8 Grove conn...
Grove Shield for Pi Pico v1.0 is an expansion board for Raspberry Pi Pico designed by Seeed Studio for the orderliness of your connected sensors when you develop projects with Pico. It provides fem...
Seeed 101020001 Grove - HCHO Sensor is a semiconductor VOC gas sensor. It uses the VOC sensor WSP2110 whose conductivity changes with the concentration of VOC gas in the air. With a circuit, the co...
From the Grove modular connector prototyping system is the Grove - Button . The momentary push button outputs a HIGH when pressed and a LOW when released.
Seeed 101020004 Grove - Switch(P) is to toggle the switch handle to make the circuit on or off, so as to achieve the purpose of switching the circuit. It features that flexible operation which give...
Seeed 101020006 Grove - Gas Sensor(MQ3) module is useful for gas leakage detecting (in home and industry). It can detect LPG, i-butane, methane, alcohol, hydrogen, and smoke. Measurements can be ta...
The Grove Moisture Sensor from Seeed Studio has two conductive prongs which can be pushed into soil or other substrate to measure the water content. It returns the moisture as an analogue signal, a...
The Grove Ultrasonic Range Finder from Seeed Studio emits ultrasonic pulses and times the return signal to establish the distance between the sensor and a reflective object. It can measure distance...
The Grove Temperature & Humidity Sensor from Seeed Studio is factory calibrated to ensure it functions well in your project.With and accuracy of ±2°C and ±5%RH this sensor is an easy choice for mos...
Seeed 101020013 Grove - RTC(DS1307) is based on the clock chip DS1307 and supports I2C communication. It uses a Lithium cell battery (CR1225) as it is low cost and very energy efficient. It can run...
From the Grove modular connector prototyping system is the Grove - Temperature Sensor. The sensor uses an onboard thermistor to measure ambient temperature over an operating range of -40 to 125°C, ...
Seeed 101020016 Grove - Infrared Receiver is used to receive infrared signals and remote control detection. The IR detector has a demodulator inside that looks for modulated IR at 38 kHz. The Infra...
Seeed 101020017 Grove - Rotary Angle Sensor or potentiometer is also known as a pot meter or Pot twig produces analog output between 0 and Vcc (5V DC with Seeeduino) on its D1 connector. The angula...
The Grove Water Sensor from Seeed Studio can be connected to a digital input to detect the presence of water or to an analogue input to measure the amount of water. Applications include tank overfl...
The Grove Temperature & Humidity Sensor from Seeed Studio is factory calibrated to ensure it functions well in your project. With and accuracy of 0.3°C and 2%rh this sensor is an easy choice for mo...
The Grove PIR Motion Sensor from Seeed Studio detects movement at up to 3m with a detection angle of 120°. When something intrudes into the detection area the sensor raises its output line to a log...
The Grove - Sound Sensor from Seeed Studio uses the combination of a simple electret microphone and a power amplifier to measure ambient sound levels. The sensor outputs an analogue value which is ...
Seeed 101020025 Grove - Tilt Switch is the equivalent of a button which has a two ball type single direction tilt sensitive trigger switch. Inside the tilt switch is a pair of balls that make conta...
Seeed 101020027 Grove - Electricity Sensor module is based on the TA12-200 current transformer which can change large alternating current into a small amplitude. You can use it to test large altern...
The Grove Thumb Joystick from Seeed Studio has two analogue outputs, one each for X and Y. The stick also has a push button, when it is pressed the analogue lines are set to maximum, otherwise they...
The Grove Digital Light Sensor from Seeed Studio gives you three detection modes, infra-red only, visible light only , and the two combined. The sensor returns a 16-bit value for the light intensit...
The Grove Piezo Vibration sensor from Seeed Studio detects vibration and outputs a logic 1 when it exceeds a threshold set by the onboard potentiometer. Applications include car alarms, security sy...
Seeed 101020033 Grove - Ear-clip Heart Rate Sensor kit contains a clip and a receiver module. The heart rate measure kit can be used to monitor heart rate of patient and athlete. The result can be ...
Seeed 101020035 Grove - Protoshield - This Grove allows you to add your own circuitry or components to your Grove system prototypes. It gives you access to all four lines from the grove connector c...
Seeed 101020036 Grove - Slide Potentiometer module incorporates a linear variable resistor with a maximum resistance of 10KΩ. When you move the slider from one side to the other, its output voltage...
The Grove Touch Sensor module is an ideal alternative for a mechanical pushbutton. The simple device uses the TTP223-B touch detector IC to measures the capacitance of a metallic pad. When a finger...
The Grove Magnetic Switch from Seeed Studio contains a dry reed switch that can be activated by a permanent magnet or electromagnet. The normally open switch is connected to a digital line and has ...
The Grove 3-axis Digital Accelerometer from Seeed Studio measures up to ±1.5g with a resolution of 6-bits. Connect this sensor to an I2C port on a Grove main board and use the downloadable library ...
Seeed 101020042 Grove - 80cm Infrared Proximity Sensor is quite small and uses a tiny connector called the Japan Solderless Terminal (JST). These connectors have three wires: Ground, VCC, and Outpu...
Seeed 101020043 Grove - UV Sensor is used for detecting the intensity of ultraviolet (UV) radiation. This form of electromagnetic radiation has shorter wavelengths than visible radiation. You can a...
Seeed 101020044 Grove - Alcohol Sensor is a complete alcohol sensor module, based on MQ303A. It has good sensitivity and fast response to alcohol.Grove - Alcohol Sensor is a complete alcohol sensor...
The Grove Galvanic Skin Response sensor from Seeed Studio measures the electrical conductivity of the skin, which has been linked to sweat production due to strong emotion. It is supplied with two ...
The Grove - 3-axis Digital Accelerometer from Seeed Studio measures up to ±16g with a resolution of 10-bits. Connect this sensor to an I2C port on a Grove main board and use the downloadable librar...
Seeed 101020055 Grove - Gas Sensor(MQ2) module is useful for gas leakage detecting (in home and industry). It can detect LPG, i-butane, methane, alcohol, hydrogen and smoke. Based on its fast respo...
Seeed 101020058 Grove - EMG Detector gathers small human muscle signals then processes them with a 2th amplify and filter. The output signal can be recognized by Arduino and can be added into your ...
The Grove Sound Sensor from Seeed Studio measures the ambient sound level and outputs it via single analogue line to any microcontroller with a spare ADC input and matching supply voltage.
Seeed 101020067 Grove - Carbon Dioxide Sensor(MH-Z16) is an infrared CO2 detection sensor which features high sensitivity and high resolution. With good selectivity, oxygen-dependent, long life, bu...
Seeed 101020071 Grove - 3-Axis Digital Accelerometer(±400g) is a low power high performance 3-axis linear accelerometer belonging to the "nano" family, with digital I2C serial interface standard ou...
The Grove Electromagnet from Seeed Studio will hold up to 1kg when energised with only 400mA at 5V DC. Because this current is beyond the capability of most microcontrollers there is an on-board lo...
Seeed 101020074 Grove - Temperature & Humidity Sensor (High-Accuracy & Mini) gives you temperature and relative humidity information at the same time. It utilizes a TH02 sensor, which is a digital ...
Seeed 101020076 Grove - Luminance Sensor provides the linear transform lumen intensity for the output voltage levels and would be suitable for application in the field of human intelligence.
Seeed 101020078 Grove - Air quality sensor v1.3 is designed for indoor air quality testing. It can respond to carbon monoxide, alcohol, acetone, thinner, formaldehyde, and other slightly toxic gase...
Seeed 101020089 Grove - Sunlight Sensor - SI1145 is a multi-channel digital light sensor which has the ability to detect UV light, visible light, and infrared light. It offers excellent performance...
Seeed 101020090 Grove - Water Atomization v1.0 is a perfect module for a humidifier with Arduino. You can also develop more advanced and interesting projects with digital scent technology and any o...
From the Grove modular connector prototyping system is the Grove - Light Sensor v1.2. This updated version gives higher reliability and sensitivity. The sensor is designed to measure light levels a...
Seeed 101020172 Grove - Line Finder v1.1 is designed for a line-following robot. It has an IR emitting LED and an IR-sensitive phototransistor which can output a digital signal to a microcontroller...
The Grove - Infrared Reflective Sensor from Seeed Studio allows your Pi or Arduino to sense the brightness reflected from a surface. This can be applied to sensing the presence or absence of an obj...
The Grove Barometer sensor is a low cost, high-precision environmental sensor that is based on the new BMP280 sensor, an upgraded version of the BMP180. The sensor can carry out precise measurement...